Exercise 3.4: Axes with logarithmic scale and error bars

---

Sometimes you need to plot your data with a logarithmic scale. As an example, let’s consider the classic genetic switch engineered by Jim Collins and coworkers (Gardner, et al., Nature, 403, 339, 2000). This genetic switch was incorporated into E. coli and is inducible by adjusting the concentration of the lactose analog IPTG. The readout is the fluorescence intensity of GFP.

The data set has the IPTG concentrations and GFP fluorescence intensity. The data are in the file ~/git/data/collins_switch.csv. Let’s look at it.

!cat data/collins_switch.csv

# Data digitized from Fig. 5a of Gardner, et al., *Nature*, **403**, 339, 2000. The last column gives the standard error of the mean normalized GFP intensity.
[IPTG] (mM),normalized GFP expression (a.u.),sem
0.001000,0.004090,0.003475
0.010000,0.010225,0.002268
0.020000,0.022495,0.004781
0.030000,0.034765,0.003000
0.040000,0.067485,0.006604
0.040000,0.668712,0.087862
0.060000,0.740286,0.045853
0.100000,0.840491,0.058986
0.300000,0.936605,0.026931
0.600000,0.961145,0.093553
1.000000,0.940695,0.037624
3.000000,0.852761,0.059035
6.000000,0.910020,0.051052
10.000000,0.893661,0.042773

It has two rows of non-data. Then, Column 1 is the IPTG concentration, column 2 is the normalized GFP expression level, and the last column is the standard error of the mean normalized GFP intensity. This gives the error bars, which we will plot momentarily. For now, we will just plot IPTG versus normalized GFP intensity.

In looking at the data set, note that there are two entries for [IPTG] = 0.04 mM. At this concentration, the switch happens, and there are two populations of cells, one with high expression of GFP and one with low. The two data points represent these two populations of cells.

a) Now, let’s make a plot of IPTG versus GFP.

1. Load in the data set using Pandas. Make sure you use the comment kwarg of pd.read_csv() properly.

2. Make a plot of normalized GFP intensity (y-axis) versus IPTG concentration (x-axis).

b) Now that you have done that, there are some problems with the plot. It is really hard to see the data points with low concentrations of IPTG. In fact, looking at the data set, the concentration of IPTG varies over four orders of magnitude. When you have data like this, it is wise to plot them on a logarithmic scale. You can specify the x-axis as logarithmic when you instantiate a figure with bokeh.plotting.figure() by using the x_axis_type='log' kwarg. (The obvious analogous kwarg applied for the y-axis.) For this data set, it is definitely best to have the x-axis on a logarithmic scale. Remake the plot you just did with the x-axis logarithmically scaled.

c) The data set also contains the standard error of the mean, or SEM. The SEM is often displayed on plots as error bars. Now construct the plot with error bars.

1. Add columns error_low and error_high to the data frame containing the Collins data. These will set the bottoms and tops of the error bars. You should base the values in these columns on the standard error of the mean (sem). Assuming a Gaussian model, the 95% confidence interval is ±1.96 times the s.e.m.

2. Make a plot with the measured expression levels and the error bars. Hint: Check out the Bokeh docs and think about what kind of glyph works best for error bars.

Solution

---

import pandas as pd

import bokeh.io
import bokeh.plotting

bokeh.io.output_notebook()

Loading BokehJS ...

a) The initial plot is straightforward. We load in the data and directly make the plot.

# Load in the data
df = pd.read_csv('data/collins_switch.csv', comment='#')

# For convenience
x = '[IPTG] (mM)'
y = 'normalized GFP expression (a.u.)'

# Make the plot
p = bokeh.plotting.figure(
    frame_height=300,
    frame_width=450,
    x_axis_label=x,
    y_axis_label=y,
)

p.circle(
    source=df,
    x=x,
    y=y,
)

bokeh.io.show(p)

b) We clearly need the \(x\)-axis to be on a log scale, so let’s remake the plot.

# Make the plot
p = bokeh.plotting.figure(
    height=300,
    width=450,
    x_axis_label=x,
    y_axis_label=y,
    x_axis_type='log',
)

p.circle(
    source=df,
    x=x,
    y=y,
)

bokeh.io.show(p)

c) We start be adding the tops and bottoms of the error bars.

# Add error bars to the DataFrame
df['error_low'] = df['normalized GFP expression (a.u.)'] - 1.96*df['sem']
df['error_high'] = df['normalized GFP expression (a.u.)'] + 1.96*df['sem']

Now, we add them to the plot using the segment() method.

# Add error bars
p.segment(
    source=df,
    x0=x,
    y0='error_low',
    x1=x,
    y1='error_high',
    line_width=2,
)

bokeh.io.show(p)

Using the interactivity, you can zoom in on the point with the smalled IPTG concentration. Note the value of interactive graphics here. Even though the error bar is smaller than the dot on the zoomed-out plot, it is resolvable upon zooming in, which is impossible even with vector graphics. Note also a common problem with using an s.e.m. to compute error bars. The result is something unphysical; the error bar extends below zero. In general using s.e.m. for error bars is a not a good idea, and we will cover better ways of computing error bars when we discuss hacker stats in upcoming lessons.

Computing environment

%load_ext watermark
%watermark -v -p pandas,bokeh,jupyterlab

Python implementation: CPython
Python version       : 3.9.12
IPython version      : 8.3.0

pandas    : 1.4.2
bokeh     : 2.4.2
jupyterlab: 3.3.2